+8618611929790

Vehicle Centering Device for Headlight Test Lane

Test Bench

Vehicle straightener/centering device for headlight test lanes: pneumatic symmetric expansion, 0.125° accuracy, <5s per alignment.

Product Details

Automotive aligner BZ-3B/BZ-3H (for light detection station)

The car aligner is used to align the vehicle entering the inspection station, so that the longitudinal centerline of the vehicle coincides with the detection centerline of the light meter (and the detection equipment such as the corner meter). If the vehicle does not stop, the left and right deviations detected by the light detection are meaningless - the regulator standardizes the action of "stopping" and eliminates the retest and judgment disputes caused by the parking position from the source.

The BZ-3B/BZ-3H adopts a cylinder symmetrical expansion structure: the front expansion rod is in a retracted state, and the vehicle is centered along the centerline of the driving; the cylinder pushes the left and right expansion rods to synchronously translate outward, and the center of the vehicle is aligned with the center of the driving center after the wheels are fitted on both sides.Alignment accuracy 0.125°, single alignment time < 5 seconds, does not occupy the detection beat, it is suitable for automotive safety performance testing line, automotive factory testing (assembly) line, and used in conjunction with lighting instruments, corner meters and other equipment.

I. Purpose and Scope of Application

  • Used to align the vehicle under inspection in front of the inspection station, so that the longitudinal center line of the vehicle is aligned with the inspector;
  • Suitable for automotive safety performance testing lines, automotive factory testing lines/assembly lines and other occasions, and used in conjunction with corner meters, lighting instruments and other equipment;
  • BZ-3B: Suitable for axle load mass not greater than3500 kgvarious types of automobiles;
  • BZ-3H: Suitable for axle load mass not greater than3000 kgVarious types of cars.

2.Main Technical Parameters

ItemBZ-3BBZ-3H
Allowed axle load mass≤ 3500 kg3000 kg
Expansion Range800 ~ 1600mm800 ~ 1600mm
Applicable wheelbase2600 ~ 4300mm1800 ~ 3500mm
Straightening accuracy125:0 .125:0 .
Straighten time5 Seconds5 Seconds
Way of DrivingCylinder pneumaticCylinder pneumatic

III. Working Principle and Main Structure

The aligner consists of a front aligner and a rear aligner. The front and rear mainframe structures are the same, and they are all composed of a lower frame, an upper frame, a cylinder, a drum, an expansion rod, etc. The rollers are mounted on the upper frame to support the wheels; the expansion rods translate left and right.

  • 1-Lower frame 2-Upper frame 3-Cylinder 4-Roller
  • 5— Expansion lever 6— Middle cover 7— Guide shaft 8— Side cover

汽车摆正器 BZ-3B / BZ-3H 结构示意图:1—下框架 2—上框架 3—气缸 4—滚筒 5—扩张杆 6—中间盖板 7—导向轴 8—边盖板
Figure 1 Schematic diagram of the structure (upper: side view/lower: top view, size unit mm)

Working process: The expansion rod retracting → vehicle is centered on the regulator, and the front and rear wheels are located on the outer side of the expansion rod. The → cylinder pushes the expansion rod to move → symmetrically left and right to fit the wheels. The vehicle center is aligned with the driving center, and the → detection is completed. The expansion rod retracts the minimum position and then the vehicle drives away.

4. Product Features

  • Symmetrical expansion, auto-alignment:The left and right expansion rods are synchronously driven by cylinders and bidirectionally fit the wheels, eliminating the need to manually move the vehicle repeatedly;
  • FasterSingle straightening time < 5 seconds, without dragging the detection line beat;
  • by:The alignment accuracy is 0.125°, which meets the alignment requirements of lighting, corners, side slips and other items;
  • No Fetal Injury:The wheels are supported by rollers, the expansion frame translation is not blocked, and the straightening process does not produce lateral tyre rubbing;
  • Wide model coverage:BZ-3B applies to wheelbase 2600 ~ 4300mm, BZ-3H applies to wheelbase 1800 ~ 3500mm, taking into account both passenger cars and light commercial vehicles;
  • Anterior-Posterior Split Structure:Front and rear aligners are installed separately to accommodate vehicles with different wheelbases;
  • Pneumatic drive:No hydraulic system, simple structure and small maintenance.

V. Installation and Use Points

Venue:Sufficient space must be left at the workshop entrance and exit. The entrance should ensure that vehicles can drive straight in, and the exit should ensure that vehicles turn only after their wheels have completely cleared the equipment. Please check the foundation drawing with the manufacturer before foundation construction.

Gas SourceIt is recommended to set up a separate air pump room outside the workshop and leave ventilation holes. The workshop should be supplied with 1 MPa of air and equipped with a 0.8 m³ (2.5 kW or 4 kW) air pump.

InstallAdjust the equipment's running centerline to coincide with the running centerline of the test line. Use a spirit level (or level gauge) placed on the roller to check that the upper surface of the frame is level with the ground and that the busbar on the roller is horizontal. After leveling, tighten the nuts and adjust the side jacking bolts to secure the frame. Pour concrete into the gaps between the leveling bolts, the bottom of the enclosure, and the front and rear of the frame and the foundation to ensure good contact between the bottom of the main unit and the foundation.

使用注意:

  • 严禁人员在摆正器上穿行,测试中车辆前后严禁站人或通行;
  • 不允许轴载质量大于设备最大承载质量的车辆检测或通过;
  • 受检车辆轮胎气压应达到规定值,底盘及胎面粘附的泥砂、石块须清除干净;
  • 车辆按行车中心线低速、平稳驶入驶出,严禁急刹车;驶入驶出时扩张杆须处于最小状态;
  • 检测应在车辆空载状态下进行;雨天或洗车后须待水渍不再滴落到设备上再检测,地基坑内不得进水。

六、维护与保养

  • 每天:检查各滚筒转动是否灵活,清洁滚筒表面污物;
  • 每周:检查各气缸工作是否正常、扩张杆行程是否符合要求;
  • 每月:检查各滚筒轴承,出现异响或转动不灵活应及时调整检修,必要时更换轴承;
  • 每季度:检查各螺栓、螺钉是否紧固。

如需按车辆轴载/轴距选型,或需要灯光检测工位的整体配套方案,欢迎联系我们提供选型建议与地基图核对。

FAQ

With 8-camera 3D dynamic measurement, accuracy reaches ±0.02° without periodic calibration.
Available in 3t/10t/13t series covering cars, trucks and buses, with optional ABS simulation and EBD evaluation.
Contact Us
WeChat QR